JUMO - JUMO digiLine O-DO S10 Digital optical sensor for dissolved oxygen in aqueous solutions

JUMO is a solution provider for the measuring ranges temperature, liquid analysis, pressure, level, flow, and humidity, as well as products for registration, monitoring, control, and automation.


JUMO digiLine O-DO S10 Digital optical sensor for dissolved oxygen in aqueous solutions - 202614/10-37-21-30/000

Product JUMO digiLine O-DO S10 Digital optical sensor for dissolved oxygen in aqueous solutions
Brand JUMO
Product Price 0 LKR
Datasheet Not Available

Description

General

The JUMO digiLine O-DO S10 is an intelligent sensor for measuring dissolved oxygen. The oxygen measurement takes place in accordance with the optical measuring principle of luminescence quenching according to ASTM D888-05. This results in the following benefits for the user:

  • No replacement of electrolytes
  • No polarization voltage required
  • No minimum inflow
  • Greater calibration intervals due to low drift behavior
  • Reliable measurement with long-term stability

The measured value for dissolved oxygen is automatically compensated to account for the temperature influence. In addition, the measured value can be compensated by the oxygen sensor with regard to the determining factors air pressure and salinity (if necessary using external sensors).

The JUMO digiLine O-DO S10 has 2 interfaces that can be used to transfer the measured value from the sensor to the measuring device/automation device. Communication takes place using a digital interface via RS485 Modbus RTU protocol or as an analog signal via the two-wire current interface (4 to 20 mA).

Configuration, parametrization, and calibration data is stored in the electronic components in the sensor of the JUMO digiLine O-DO S10. Sensor-specific specifications and measuring point information can also be stored and called up. In addition, a log book with the last 10 successful calibrations is available; this provides the user with an overview of the previous calibration history.

Furthermore, the sensor is equipped with the capability for self-diagnostics, in order to determine possible malfunctions. The information is output as a warning or error message. The sensor is streamlined and has a robust construction. The sensor cap is easy to replace if it becomes worn. The sensor body of the JUMO digiLine O-DO S10 consists of PVC material, which allows it to be used in fresh water and salt water. A fixed cable with a 5-pole M12 connector is mounted on the sensor. The electrical connection to a measuring or automation device is quick and easy to establish. 2 connection options are available for mounting in a fitting – the Rp 1 thread on the sensor shaft or a mounting set G 1 available as accessories.

  • Typical areas of application
  • Drinking water monitoring
  • Protection of water bodies
  • Fish breeding (fresh and salt water)
  • Municipal and industrial sewage treatment plants
  • General water and wastewater engineering
  • Universities and teaching institutions0

Features

  • Output of measured value for oxygen in % Sat, % Vol, ppm, hPa pO2
  • Suitable for fresh and salt water
  • Immediately ready for use due to factory calibrations
  • RS485 Modbus RTU interface
  • Analog output 4 to 20 mA (two-wire current interface)

Specifications

  • Make: JUMO
  • Model: 202614/10-37-21-30/000
  • Part Number: 00730250
  • Basic type: 202614 JUMO digiLine O-DO S10
  • Basic type extension: 10 Standard design
  • Measuring range: 37 0 to 20 ppm (mg/l)a a Factory setting = 0 to 200 % Sat. To provide 0 to 20 ppm (mg/l) output, this setting must be changed in the sensor configuration.
  • Electrical connection: 21 Fixed cable with M12 connector
  • Length of permanent cable: 30 30 m
  • Extra codes: 000 None

Contacts and Delivery

Fieldinstruments.lk
50/3, Angampitiya Rd, Ethul Kotte, Sri Lanka. 10100.
Phone: +94718555888 Email: info@fieldinstruments.lk